Sensor module 3D Models

Find the best Sensor module 3D Models, free download in STL, FBX, GLB, OBJ, 3MF, USDZ for 3D modeling and creation in Blender, 3D printing, game developing, animation, eCommerce, AR/VR and etc. Generated by Tripo AI 3D Generator.

You May Also Like :

fop fancy

Anonymous1752600177

Anonymous1759167426

Anonymous1769017029

1. Cuerpo principal Crear un **bloque base** 150 mm × 80 mm × 40 mm Aplicar:fillet (redondeo)** en bordes: 6–10 mm
Resultado: cuerpo compacto con bordes suaves 2. Inclinación frontal (clave para diseño)
Cortar o inclinar la cara frontal unos **10–15° Esto le da ese look tecnológico3. Módulo de sensores (parte superior/frontal)Crear un rectángulo elevado o embebidoTamaño aprox: 40 × 40 mmDentro:Círculo central (sensor):** ~25 mm diámetroAlrededor:Anillo LED** (extrusión fina) Grosor: 2–3 mm4. Ventana de sensoresMaterial visual:Translúcido mate Geometría:Superficie ligeramente hundida (1–2 mm)5. Zona de agarre (laterales)Crear un área lateral:70–80% del largoHundir ligeramente:1–2 mmAplicar textura:tipo “noise” o patrón rugosa6. Base inferiorLigera curvatura o plano inclinadoOpcional: puerto tipo USB-C 🎨 Materiales (para render) Cuerpo:Blanco marfil (#F5F4F0)Roughness medio (semi-mate) Detalles:Grafito (#2B2B2B)LED:
Emission azul (#0A84FF) Sensor: Vidrio/plástico mate

Anonymous1777675354

Anonymous1777123703

Anonymous1774549415

Step 1: Define Your Nets (Power Rails): Create distinct power lines for 5V and 3.3V. Since the ESP32 and LoRa SX1278 operate at 3.3V, ensure they are connected to a regulated 3.3V source to prevent damage.

Step 2: Establish the SPI Bus for LoRa: Connect the LoRa SX1278 to the ESP32 using the SPI protocol pins: SCK (GPIO18), MISO (GPIO19), MOSI (GPIO23), and NSS/CS (GPIO5).

Step 3: Connect Sensors and GPS:

Ultrasonic Sensor: Connect the Trigger and Echo pins to the ESP32. Use a voltage divider on the Echo pin to step down the 5V signal to 3.3V for the ESP32’s safety.

GPS Module: Connect the TX/RX pins to the ESP32’s hardware serial pins (GPIO16/17).

Step 4: Add Protection and Decoupling: Place 0.1µF and 10µF decoupling capacitors near the power pins of the ESP32 and LoRa module to filter out electrical noise and stabilize signals.

Anonymous1775101996

Anonymous1775450120

un support de montage pour capteur ToF VL53L0X (module HW-843) destiné à un petit robot résolveur de labyrinthe.
Le support doit être un cadre ouvert à l’arrière (~30mm × 45mm × 15mm) avec quatre pattes de retenue aux coins pour maintenir le PCB (15,7mm × 12,6mm × 2mm), une fenêtre ouverte sur la face avant pour laisser le capteur entièrement dégagé, et deux trous M3 alignés sur les oreilles du PCB espacés d’environ 22mm. La base doit inclure une bride de fixation avec deux trous M3 pour le montage sur le châssis. L’arrière doit rester entièrement ouvert pour permettre un accès libre aux broches du connecteur.
.

Anonymous1716696397

Anonymous1774505170

A sleek minimalist wrist-worn rehabilitation wearable device, soft matte dark green silicone band with magnetic snap closure, small embedded sensor module
with subtle LED indicator, IMU sensor visible through semi-transparent housing, medical-grade breathable mesh fabric texture, floating on clean white
background, soft studio lighting, product photography style, 3D render, isometric view, no hand shown, ultra clean Apple-style product shot, 8K quality

Anonymous1770201201

Anonymous1775294458

Anonymous1754204695

Transform this flat 2D illustration into a detailed, three-dimensional style image

Anonymous1774918282

Anonymous1758077406

Anonymous1752754805

Make only one model not three of them, am just showing how the sensor looks like

Anonymous1774822948